wj buggy build - Page 2 - North American Grand Cherokee Association

96liftedzj · 07-10-2012, 08:37 PM

yes then closed in the cab. had ac,heat, and seated 5 in comfort...even the rear defrost and third brake light worked

96liftedzj · 07-10-2012, 08:39 PM

i also moved the fuel tank up 8" and the filler as in the "bed"

96liftedzj · 07-11-2012, 03:39 PM

done a little rear bar design....just mock up right now

but not sure if i am liking it......need to do more design and see if i can get it looking better

DUBJ · 07-11-2012, 04:07 PM

Hey give yourself some time to think about fabrication i think that would look good if you do it right. I was thinking you could weld some extention on to the role bar that would extend out over the roof so you would have some role over protection

96liftedzj · 07-11-2012, 04:46 PM

i am thinking of lowering it about 3"'s and move the first bar under the roof and the flat bars on the side have them about an inch above the old window openings. but yes a exo cage will tie in to this bar.

96liftedzj · 07-14-2012, 03:06 PM

it has been moved to the bottom of to do list.. going to fix my 54' ford customline first.was my dads but he recently died so it just became my priority

biggoofy · 07-17-2012, 11:57 AM

said it before ill say it again this isnt a buggy!

07-10-2012, 08:37 PM	#11
96liftedzj Member Grand Rookie Join Date: Apr 2010 Location: middleburg,fl Posts: 59	yes then closed in the cab. had ac,heat, and seated 5 in comfort...even the rear defrost and third brake light worked __________________ 91 ranger xcab 4x4,4.0 v6,5spd,manual tcase and hubs...pretty stock for now 93 jeep zj,5.2,auto,4x4

07-10-2012, 08:39 PM	#12
96liftedzj Member Grand Rookie Join Date: Apr 2010 Location: middleburg,fl Posts: 59	i also moved the fuel tank up 8" and the filler as in the "bed" __________________ 91 ranger xcab 4x4,4.0 v6,5spd,manual tcase and hubs...pretty stock for now 93 jeep zj,5.2,auto,4x4

07-11-2012, 03:39 PM	#13
96liftedzj Member Grand Rookie Join Date: Apr 2010 Location: middleburg,fl Posts: 59	done a little rear bar design....just mock up right now but not sure if i am liking it......need to do more design and see if i can get it looking better __________________ 91 ranger xcab 4x4,4.0 v6,5spd,manual tcase and hubs...pretty stock for now 93 jeep zj,5.2,auto,4x4

07-11-2012, 04:46 PM	#15
96liftedzj Member Grand Rookie Join Date: Apr 2010 Location: middleburg,fl Posts: 59	i am thinking of lowering it about 3"'s and move the first bar under the roof and the flat bars on the side have them about an inch above the old window openings. but yes a exo cage will tie in to this bar. __________________ 91 ranger xcab 4x4,4.0 v6,5spd,manual tcase and hubs...pretty stock for now 93 jeep zj,5.2,auto,4x4

07-14-2012, 03:06 PM	#16
96liftedzj Member Grand Rookie Join Date: Apr 2010 Location: middleburg,fl Posts: 59	it has been moved to the bottom of to do list.. going to fix my 54' ford customline first.was my dads but he recently died so it just became my priority __________________ 91 ranger xcab 4x4,4.0 v6,5spd,manual tcase and hubs...pretty stock for now 93 jeep zj,5.2,auto,4x4

07-11-2012, 04:07 PM	#14
DUBJ Member Grand Rookie Join Date: Apr 2012 Location: Williamsport Pa Posts: 43	Hey give yourself some time to think about fabrication i think that would look good if you do it right. I was thinking you could weld some extention on to the role bar that would extend out over the roof so you would have some role over protection

07-17-2012, 11:57 AM	#17
biggoofy Local Jack* Grand Rookie** Join Date: May 2012 Location: Troy nc Posts: 33	said it before ill say it again this isnt a buggy! __________________ Zack 96 ZJ HP44 / 9" for those really tough parking lots

Remove Advertisements Sponsored Links
Nagca.com Advertisement

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode